INSTALL

** Overview **

This repository contains everything that is needed to set up and build the 
Tensegrity simulators. The 'env' and 'build' directories that are created
during setup are considered to be local directories and are ignored in the 
repository. If you run into problems, you can always delete these and run
setup again. 

To get started, read the below instructions, then run the setup script 
(setup.sh). It will walk you through the process of getting everything 
configured and installed. If you already have some things installed in 
the standard locations, setup will find those so that
you don't have to reinstall. However, this functionality may be limited
based on your linux distribution, so if you're not using Ubuntu 13.10 or 
14.04, be sure to read below and confirm you have the necessary packages
in your $PATH. You can run setup as many times as you like without hurting 
anything.


** Linux / Mac Installation **

  ** Prerequisites/Dependencies **

  - Some Linux prerequisites, outside of the setup script file. Make
    sure the following are installed: 
    
    Ubuntu (you can use sudo apt-get install):
	- g++ (the compiler for cmake)
	- libglib2.0-dev
	- curl
	- freeglut3
	- freeglut3-dev (glut for bullet graphics)
	- cmake
	- build-essential
        - unzip

    Fedora/CentOS (you can use sudo yum install):
	- gcc-c++ (the compiler for cmake)
	- glib2-devel and glib2-devel.i686
	- curl
	- freeglut
	- freeglut-devel
	- cmake
	- build-essential
	- unzip

    MAC OSX (please read the detailed instructions below for OSX 10.9 at the end of this file)
	-gcc/g++ 4.5 (via Macports or Homebrew)
		
  - Also if available, it's sometimes easier to install cmake (and/or boost)
    from your distro. On ubuntu, sudo apt-get install cmake.
    If you do this, the script is designed to detect system-wide cmake
    installations on both Linux and Mac; however, it only correctly
    detects boost installations on Mac.

  - Installing libboost-all-dev under Ubuntu does NOT place these files
    where our install script can see them. At the moment, it's easier to 
    just have our installer download and compile its own version of
    libboost-1.53.0-dev, as counterintuitive as that seems. See a known
    issue below about this compilation under Ubuntu 14.04.

  ** Running the setup script **

  - If you want to specify setup options, copy the files in
    conf/default/ to conf/, removing the .default
    (for example conf/default/bullet.conf.default becomes conf/bullet.conf)
    and edit as desired. This can save you time if you already have Boost 
    installed.
    You can also just run setup.sh -- it will create the .conf files 
    for you and allow you to set certain options like the location of your 
    bullet build if you already have one. 

  - Run setup.sh. (sh setup.sh or bash setup.sh)

  - The setup.sh script may be run multiple times without hurting anything. 

  - To build the the src tree, run bin/build.sh 

    The resulting executables will be located under the 'build' folder.

    To run an app, go to build/examples/SomeApp and run the executable.
    (for example: build/examples/3_prism/AppPrismModel)

    To build a specific app (after making changes to the source, for instance),
    go to build/dev/myApp and run 'make' 

  - Create a project in your favorite IDE using the equivalent of 
    'Create a project using existing source' to point your project to the src 
    directory. See below for more instructions.


** Development Environments **

    During setup, an 'env' directory will be created. This directory is intended to
    be local to your system and is ignored in the repository. It contains builds of
    the software installed by setup as well as symlinks needed by CMakeLists.txt
    for the build process.

    After you create a new project using the existing source (the 'src' directory), 
    add the include and library paths that have been created during setup. Note
    that all relative paths listed below (e.g. env/lib) are relative to this 
    directory. 

      - Add the following to your c++ include paths:

        env/include/bullet
        env/include/boost

      - You'll also want to add the standard include paths if they're not 
        already present, e.g.:

        /usr/include
        /usr/local/include
        /usr/include/c++/4.2.1 (location of cstdlib header on your system)

      - Add the following to your c++ library paths:

        env/lib

      - If you are working on Mac OSX you will need to include the default framework location

        /Library/Frameworks

      - Also add the standard library paths (may be slightly different for you):

        /usr/lib
        /usr/local/lib

** Build Options **

  - After the first install, note the following options are available with build.sh (run build.sh -h for an up to date list)
  
    positional arguments:
    build_path            Path to build (relative to src, e.g. 'BasicApp' or
                           'lib/Example'). Defaults to all if not specified, includes dependancies.
   
    optional arguments:
    -h       Show this help message and exit
    -c       Run 'make clean' before make/make install on non-library sources
    -w       Show compiler warnings when building
    -t       Build test/ rather than src/
    -r       Build test/ rather than src/ *and* run all tests after compilation.
    -i       Build test_integration/ rather than src/
    -g       Build test_integration/ rather than src/ *and* run all tests after compilation.

** Manual Installation **

  - Install cmake (see http://www.cmake.org for details)

  - Install boost in the standard manner (see http://www.boost.org)
        
  - Create an 'env' directory in the same directory as this INSTALL file. 

    mkdir env
  
  - Create the necessary subdirectories under env:

    cd env
    mkdir bin build downloads include lib
    cd ..

    
  - Create a symlink to cmake under env/bin:
    
    cd env/bin
    ln -s `which cmake` # (or just provide the path, e.g. ln -s /usr/bin/cmake)
    cd ../..  # back to top level

  - Download and build Bullet Physics:
    
    cd env/downloads
    curl -k -L -O http://bullet.googlecode.com/files/bullet-2.82-r2704.tgz
    cd ../build
    tar xzvf ../downloads/bullet-2.82-r2704.tgz

    cd bullet-2.82-r2704/
    path_to_env=`pwd`/../../../env
    "$path_to_env/bin/cmake" . -G "Unix Makefiles" \
        -DBUILD_SHARED_LIBS=OFF \
        -DBUILD_EXTRAS=ON \
        -DCMAKE_INSTALL_PREFIX="$path_to_env" \
        -DCMAKE_INSTALL_NAME_DIR="$path_to_env"
    make
    make install
    cd ..   # back to env/build
    
  - Create a 'bullet' symlink to your bullet build under env/build. This will 
    be expected by CMakeLists.txt
  
    ln -s bullet-2.82-r2704 bullet
    cd ../..   # back to top level
    
  - Create the necessary symlinks under env/include. The following values 
    reflect global installations of boost and gsl; adjust these values if you
    installed these packages elsewhere (e.g. using --prefix=/path/to/env).
    
    cd env/include
    ln -s /usr/local/include/boost boost
    cd ../..  # back to top level
    
    You should also have a 'bullet' directory under env/include. If not, make 
    sure to create a symlink that points to the bullet header files.
    
    - NOTE: When complete, your 'env' directory must have either directories or
      symlinks for the following elements:

      env/
        bin/
          cmake  # (executable)
        include/
          bullet/  # Bullet header files
          boost/   # Boost header files
        lib/     # Libraries will be installed here when you build the source.

  - That should do it. You can now run bin/build.sh to build your code.
    
** Troubleshooting and Known Issues **

  - Our usage of Git does not respect file permissions well enough
    on occassion. You may have to "chmod ug+x" our setup.sh and bin/build.sh
    scripts. 

  - If any of the downloads fail, there may be a corrupt file in env/downloads.
    Be sure to remove it before running setup/setup.sh again.
    Similarly, there might be a failed install directory under env/build, if
    a compilation fails. TO-DO: create a "make clean"-like function for setup.

  - Similarly, this script does not currently check for package integrity
    before extracting tarballs, and will happily attempt to extract incomplete
    downloads and then fail. If you get errors, just delete the package's 
    directory under ./env/downloads and ./env/build

  - Under Ubuntu 14.04, the compile of Boost will exit with errors even though
    it actually completes successfully. You'll get an exit message like:
         >> ...failed updating 6 targets...
         >> ...skipped 18 targets...
         >> ...updated 11024 targets...
         >> Install failed
         >> Boost initialization failed -- exiting now.
    This is fine. Just run setup.sh again to confirm everything is OK, then
    move on to running bin/build.sh

  - If you want to recompile a library, when you try and re-run ./setup.sh,
    remove not only the downloaded file and extracted files under 
    ./env/build, but also the (failed) compiled files under ./env/include 
    and ./env/lib, for example, a failed compile of Boost requires deleting 
    ./env/include/boost and everthing named "libboost" under ./env/lib

  - If you get an error when running bin/build.sh about CMake not "including"
    a GLIB directory, be sure you've installed libglib2.0-dev (Ubuntu 14.04).

  - A known bug is that some of this code will not compile without the
    position-independent-code flag, -fPIC, passed in. Though this flag should
    be enabled by default now, if you do get an error related to -fPIC, just 
    edit the CMakeLists files to include -fPIC.

  - If you are upgrading from a prior version, be sure to delete your env directory
    and reinstall it using setup.sh. There have been some changes to the patches,
    particularly the neuralNetwork code, that are incompatible.


** MAC OSX 10.9 installation problem **

	Due to the defaul library being stdlibc++ instead of stdc++, NTRT and 
	also all the dependencies (boost and bullet) has to be compiled using 
	gcc. As a temporary solution, please follow these steps:

	1) Install gcc, g++ using macports or homebrew (I used with gcc 4.5.4 through macports).
	2) Download the github directory
	3) Edit bin/setup/setup_boost.sh and uncomment this line by deleting '#':
		#sed -i '' 's/^# using gcc ;/using gcc ;/g' tools/build/v2/user-config.jam
	4)run setup.sh
	5)run bin/build.sh