locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

locales: Added translation using Weblate (Lithuanian)

Co-authored-by: Languages add-on <noreply-addon-languages@weblate.org>

docs/locales/lt/LC_MESSAGES/Axis_Twist_Compensation.po

@@ -0,0 +1,111 @@
+# Languages add-on <noreply-addon-languages@weblate.org>, 2024.
+msgid ""
+msgstr ""
+"Language: lt\n"
+"Content-Type: text/plain; charset=UTF-8\n"
+"Content-Transfer-Encoding: 8bit\n"
+
+#: docs/Axis_Twist_Compensation.md:block 1 (header)
+msgid "Axis Twist Compensation"
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 2 (paragraph)
+msgid "This document describes the [axis_twist_compensation] module."
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 3 (paragraph)
+msgid ""
+"Some printers may have a small twist in their X rail which can skew the "
+"results of a probe attached to the X carriage. This is common in printers "
+"with designs like the Prusa MK3, Sovol SV06 etc and is further described "
+"under [probe location bias](Probe_Calibrate.md#location-bias-check). It may "
+"result in probe operations such as [Bed Mesh](Bed_Mesh.md), [Screws Tilt "
+"Adjust](G-Codes.md#screws_tilt_adjust), [Z Tilt "
+"Adjust](G-Codes.md#z_tilt_adjust) etc returning inaccurate representations "
+"of the bed."
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 4 (paragraph)
+msgid ""
+"This module uses manual measurements by the user to correct the probe's "
+"results. Note that if your axis is significantly twisted it is strongly "
+"recommended to first use mechanical means to fix it prior to applying "
+"software corrections."
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 5 (paragraph)
+msgid ""
+"**Warning**: This module is not compatible with dockable probes yet and will"
+" try to probe the bed without attaching the probe if you use it."
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 6 (header)
+msgid "Overview of compensation usage"
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 7 (quote)
+msgid ""
+"**Tip:** Make sure the [probe X and Y offsets](Config_Reference.md#probe) "
+"are correctly set as they greatly influence calibration."
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 8 (ordered list)
+msgid ""
+"After setting up the [axis_twist_compensation] module, perform "
+"`AXIS_TWIST_COMPENSATION_CALIBRATE`"
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 9 (unordered list)
+msgid ""
+"The calibration wizard will prompt you to measure the probe Z offset at a "
+"few points along the bed"
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 9 (unordered list)
+msgid ""
+"The calibration defaults to 3 points but you can use the option "
+"`SAMPLE_COUNT=` to use a different number."
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 10 (ordered list)
+msgid "[Adjust your Z offset](Probe_Calibrate.md#calibrating-probe-z-offset)"
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 10 (ordered list)
+msgid ""
+"Perform automatic/probe-based bed tramming operations, such as [Screws Tilt "
+"Adjust](G-Codes.md#screws_tilt_adjust), [Z Tilt "
+"Adjust](G-Codes.md#z_tilt_adjust) etc"
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 10 (ordered list)
+msgid "Home all axis, then perform a [Bed Mesh](Bed_Mesh.md) if required"
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 10 (ordered list)
+msgid ""
+"Perform a test print, followed by any [fine-"
+"tuning](Axis_Twist_Compensation.md#fine-tuning) as desired"
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 11 (quote)
+msgid ""
+"**Tip:** Bed temperature and nozzle temperature and size do not seem to have"
+" an influence to the calibration process."
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 12 (header)
+msgid "[axis_twist_compensation] setup and commands"
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 13 (paragraph)
+msgid ""
+"Configuration options for [axis_twist_compensation] can be found in the "
+"[Configuration Reference](Config_Reference.md#axis_twist_compensation)."
+msgstr ""
+
+#: docs/Axis_Twist_Compensation.md:block 14 (paragraph)
+msgid ""
+"Commands for [axis_twist_compensation] can be found in the [G-Codes "
+"Reference](G-Codes.md#axis_twist_compensation)"
+msgstr ""