bring up to date

config/examples/Creality/Ender-2 Pro/CrealityV24S4/Configuration.h

@@ -1,6 +1,6 @@
 /**
  * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ * Copyright (c) 2024 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
  * Based on Sprinter and grbl.
  * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
@@ -20,6 +20,8 @@
  *
  */
 #pragma once
+#error "Don't build with import-2.1.x configurations!"
+#error "Use the 'bugfix...' or 'release...' configurations matching your Marlin version."
 
 /**
  * Configuration.h
@@ -68,7 +70,7 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define  MOTHERBOARD BOARD_CREALITY_ENDER2P_V24S4
+  #define MOTHERBOARD BOARD_CREALITY_ENDER2P_V24S4
 #endif
 
 /**
@@ -101,7 +103,7 @@
  * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
  * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-// #define SERIAL_PORT_2 3
+//#define SERIAL_PORT_2 3
 //#define BAUDRATE_2 250000   // :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] Enable to override BAUDRATE
 
 /**
@@ -1015,9 +1017,6 @@
     // Radius around the center where the arm cannot reach
     #define MIDDLE_DEAD_ZONE_R   0  // (mm)
 
-    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See https://www.morgan3dp.com/morgan-calibration-guide/
-    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See https://www.morgan3dp.com/morgan-calibration-guide/
-
   #elif ENABLED(MP_SCARA)
 
     #define SCARA_OFFSET_THETA1  12 // degrees
@@ -1036,23 +1035,19 @@
   #define DEFAULT_SEGMENTS_PER_SECOND 200
 
   // Length of inner and outer support arms. Measure arm lengths precisely.
-  #define TPARA_LINKAGE_1 120       // (mm)
-  #define TPARA_LINKAGE_2 120       // (mm)
+  #define TPARA_LINKAGE_1 120     // (mm)
+  #define TPARA_LINKAGE_2 120     // (mm)
 
-  // SCARA tower offset (position of Tower relative to bed zero position)
-  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
-  #define TPARA_OFFSET_X    0       // (mm)
-  #define TPARA_OFFSET_Y    0       // (mm)
-  #define TPARA_OFFSET_Z    0       // (mm)
+  // TPARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the TPARA space.
+  #define TPARA_OFFSET_X    0     // (mm)
+  #define TPARA_OFFSET_Y    0     // (mm)
+  #define TPARA_OFFSET_Z    0     // (mm)
 
   #define FEEDRATE_SCALING        // Convert XY feedrate from mm/s to degrees/s on the fly
 
   // Radius around the center where the arm cannot reach
   #define MIDDLE_DEAD_ZONE_R   0  // (mm)
-
-  // Calculated from Calibration Guide and M360 / M114. See https://www.morgan3dp.com/morgan-calibration-guide/
-  #define THETA_HOMING_OFFSET  0
-  #define PSI_HOMING_OFFSET    0
 #endif
 
 // @section polar
@@ -3058,7 +3053,7 @@
 
 //
 // Factory display for Creality CR-10 / CR-7 / Ender-3
-// https://www.aliexpress.com/item/32833148327.html
+// https://marlinfw.org/docs/hardware/controllers.html#cr10_stockdisplay
 //
 // Connect to EXP1 on RAMPS and compatible boards.
 //