-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathprinter-20231009_152725.cfg
99 lines (79 loc) · 2.98 KB
/
printer-20231009_152725.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
## DO NOT EDIT THIS FILE, IT IS A TEMPLATE. THAT YOU NEED TO COPY
# Prusa MK3s Klipper Config
# The first thing you'll need to do is go through this file and comment out / uncomment
# the files and/or settings you need.
# You'll be able to print just fine with this config as it is, but it is recommended
# that you follow these steps to properly calibrate your printer:
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
# 2) Skew Correction: https://www.klipper3d.org/skew_correction.html
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
# Read more about klipper here: https://www.klipper3d.org/Overview.html
### UI
[include mainsail.cfg]
# [include fluidd.cfg]
[mcu]
# serial: /dev/serial0 # If you are using internal RPI serial port
serial: /dev/ttyACM0 # If you are using RPI via USB connection to printer
restart_method: command
### CONTROL BOARD
[include einsy-rambo.cfg]
### BASE SETUP
[include klipper-prusa-mk3s/mk3s/display.cfg]
[include klipper-prusa-mk3s/mk3s/steppers.cfg]
[include klipper-prusa-mk3s/mk3s/tmc2130.cfg]
### EXTRUSION
# Extruder
# [include klipper-prusa-mk3s/extruders/prusa.cfg]
[include extruder.cfg]
# Hotend
[include klipper-prusa-mk3s/hotends/v6.cfg]
# [include klipper-prusa-mk3s/hotends/dragon-standard-flow.cfg]
# [include klipper-prusa-mk3s/hotends/rapido.cfg]
[extruder]
# To tune Pressure Advance see https://www.klipper3d.org/Pressure_Advance.html
# default is already set based on hotend, but you can further improve prints by calibrating it to your nozzle and material
# pressure_advance: 0.05
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
#pid_Kp: 23.862
#pid_Ki: 1.020
#pid_Kd: 139.595
## copy this from your current setting on Prusa, but make it absolute (removing -)
[probe]
z_offset = 0.685
## For faster printing enable
[printer]
max_accel: 2000
max_accel_to_decel: 2000
max_z_velocity: 20
max_z_accel: 300
## Custom bed mest probes
## Prusa has 3x3 or 7x7, you can do any variation you want
[bed_mesh]
probe_count: 7,7
# Linear correction
# Check `extruders/linear-correction` for more informations.
[include klipper-prusa-mk3s/extruders/linear-correction/linear-correction-0.cfg] # Default Prusa linear correction optimized for LDO motors
### MACROS
[include klipper-prusa-mk3s/macros.cfg]
# FIRST RUN:
# Execute these sequentially in the console, let PID tuning finish before saving
# PID_CALIBRATE HEATER=extruder TARGET=170
# SAVE_CONFIG
# PID_CALIBRATE HEATER=heater_bed TARGET=60
# SAVE_CONFIG
### The end, on the end the printer will store it's tuning data, so do not edit it.
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 50.249
#*# pid_ki = 0.601
#*# pid_kd = 1049.575
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 19.356
#*# pid_ki = 0.787
#*# pid_kd = 119.037