Skip to content

Latest commit

 

History

History
112 lines (72 loc) · 4.37 KB

README.md

File metadata and controls

112 lines (72 loc) · 4.37 KB

3D Printer Filament Width Sensor

GitHub issues

This is an optical sensor based on the ATtiny85 - 8-bit AVR Microcontrollerthat measures the plastic filament width in real time as it goes into a 3D printer extruder by using the TSL1401CL sensor.

License

Attribution-NonCommercial-ShareAlike

This project is licensed under the Attribution-NonCommercial-ShareAlike CC BY-NC-SA 4.0 license. The full legal text of the license may be found in the LICENSE.md file in this repository. For more information about this license, please visit the Creative Commons Foundation (https://creativecommons.org/licenses/by-nc-sa/4.0/).

Features

  • Measures filament width in real time to improve extrusion.

  • Can detect filament diameter of 1.75mm, 2.85mm and 3.00mm.

  • Compatible with Marlin 1.1.X, RepRap and MK4duo Firmware.

  • Can interface with a variety of 3D Printer Controller Board including:

    • RAMPS 1.2 and newer
    • RAMBo 1.2 and newer
    • Printrboard Rev B,C,D,E

  • One button calibration mode.

  • Compact PCB design (25.71mm x 19.00mm)

  • Operational Voltage: 5V

  • Reverse polarity protection.

  • Programming pins for future firmware upgrade.

  • You can buy the latest version of this board fully assembled from http://mini-mods.com

  • Filament Width Sensor Top. Filament Width Sensor Top

  • Filament Width Sensor Bottom. Filament Width Sensor Bottom

Prerequisites

  1. Access to the source code for your existing printer.

  2. Arduino IDE 1.8 or newer.

Software Configuration

Modify Configuration.h and set the appropriate filament with diameter, in this example 1.75mm filament is configured.

	#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75

Modify Configuration_adv.h on the section Filament Width Sensor, enabled by uncomment the following line.

	#define FILAMENT_WIDTH_SENSOR

Also to constantly display the nominal filament width on your 3D printer display, uncoment the following line.

	#define FILAMENT_LCD_DISPLAY

Once done, flash the modified firmware to your printer.

Hardware Installation

The following images display the correct pin location for the installation for the Filament Width Sensor.

  • RAMPS 1.4 Pinout. ramps

  • RAMBo 1.2 Pinout. rambo

  • Printrboard Rev B,C,D,E Pinout. printrboard

Basic Hardware Usage

The calibration button is used to calibrate the sensor. This will be needed for first time use or if the sensor is modified (different housing, LED, etc).

Press the calibration button while the filament is inside in the encloser to calibrate.

Hold the button for roughly 3 seconds, until the LED lights off or flashes again. The sensor is then calibrated and settings will be saved in the flash. If you press calibration without a filament inserted, you will get false readings.

Basic Software Usage

This is the list of gcodes you can use to enable the Filament Width Sensor on your slicer:

M404 Enter the nominal filament width (3mm, 1.75mm) or will display nominal filament width without parameters.

Examples:
			M404 ; Will display real time filament width
			M404 N1.75	; Set the nominal filament width to 1.75mm

M405 Turn ON Filament Sensor extrusion control. Optional D to set delay in centimeters between sensor and extruder. Always start your slicer code with this gcode.

Examples:
			M405 ; Turn on Filament Sensor extrusion control
			M405 D12 ; Turn on Filament Sensor extrusion control and set a delay of 12cm between the sensor reading and the extruder.

M406 Turn off Filament Sensor extrusion control. Always end your slicer code with this gcode.

M407 Displays measured filament diameter. In RepRapFirmware, M407 does the same as M404.

Basic Maintenance

This is an optical sensor and dust or debris can cause false or changing readings. Clean dust by blowing on the sensor or gently using a cotton swab to clean the sensor.