Shelly HomeKit 2.14.2

Support

If you use the firmware please consider a donation to support further development. Thank you for your continuous support

Changes from 2.14.1 to 2.14.2

• +2PM: Fix Reset behavior on power cut

Changes from 2.14.0 to 2.14.1

• RGBWPM: fix reuse of PWM Timers (this fixes strange problems mainly in White mode)
• Addon Support for Gen3 Devices
• Match Device IDs to Stock to avoid updating problems

Changelog for 2.14.0

New Devices

• 1 Gen3
• 1PM Gen3
• 2PM Gen3
• i4 Gen3
• PlugS Gen3
• Plus Uni

Features:

• Sensor Support for ShellyPlusUni / ShellyUNI
• Initial Power Measurement Support on Mini1PMG3/+1PMMini
• +2PM and 2PMG3 Powermeter: Use original calibration values from Device partition
• +Plug S: Support for Neopixel Status LEDs

Fixes

• +2PM HW REV01: fix powermeasurement
• +1PM do not read power coefficients / enable updating

Note that reverting for PlugS Gen3 seems currently not possible, as we have no original firmware available.

Currently reverting for Mini 1/1PM Gen3 is disabled due to problems that could arise that brick the device. Please check the corresponding support issue.

Note: If you come from stock then please be sure to update to latest stock (1.5.1!) before using this firmware

Full Changelog: 2.14.0...2.14.2

Shelly Homekit 2.14.1

Support

If you use the firmware please consider a donation to support further development. Thank you for your continuous support

Changes from 2.14.0 to 2.14.1

• RGBWPM: fix reuse of PWM Timers (this fixes strange problems mainly in White mode)
• Addon Support for Gen3 Devices
• Match Device IDs to Stock to avoid updating problems

Changelog for 2.14.0

New Devices

• 1 Gen3
• 1PM Gen3
• 2PM Gen3
• i4 Gen3
• PlugS Gen3
• Plus Uni

Features:

• Sensor Support for ShellyPlusUni / ShellyUNI
• Initial Power Measurement Support on Mini1PMG3/+1PMMini
• +2PM and 2PMG3 Powermeter: Use original calibration values from Device partition
• +Plug S: Support for Neopixel Status LEDs

Fixes

• +2PM HW REV01: fix powermeasurement
• +1PM do not read power coefficients / enable updating

Note that reverting for PlugS Gen3 seems currently not possible, as we have no original firmware available.

Currently reverting for Mini 1/1PM Gen3 is disabled due to problems that could arise that brick the device. Please check the corresponding support issue.

Note: If you come from stock then please be sure to update to latest stock (1.5.1!) before using this firmware

Full Changelog: 2.14.0...2.14.1

Shelly Homekit 2.14.0

Support

If you use and enjoy the firmware please consider a donation to support further development.

New Devices

• 1 Gen3
• 1PM Gen3
• 2PM Gen3
• i4 Gen3
• PlugS Gen3
• Plus Uni

Features:

• Sensor Support for ShellyPlusUni / ShellyUNI
• Initial Power Measurement Support on Mini1PMG3/+1PMMini
• +2PM and 2PMG3 Powermeter: Use original calibration values from Device partition
• +Plug S: Support for Neopixel Status LEDs

Fixes

• +2PM HW REV01: fix powermeasurement
• +1PM do not read power coefficients / enable updating

Note that reverting for PlugS Gen3 seems currently not possible, as we have no original firmware available.

Currently reverting for Mini 1/1PM Gen3 is disabled due to problems that could arise that brick the device. Please check the corresponding support issue.

Note: Some users experienced issues with this Firmware on 2PM Gen3: Please be sure to upgrade to latest stock (1.5.1!) before using this firmware

Full Changelog: 2.13.3...2.14.0

Shelly HomeKit 2.13.3

Support

If you use and enjoy the firmware please consider a donation to support further development.

Changelog

Fixes

• Release Pin Holding when updating from Stock Firmware (e.g. #1566)
• Fix RGBW2 behavior at 100% (again)

Updating from 2.12.X

Important: This release deliberately breaks the upgrade path from Shelly HomeKit 2.12.X for any Plus Devices (those are: +1, +1PM, +i4, +2PM, +RGBWPM, +PlugS). The reason for this is to support direct upgrade from newest stock firmware (1.4.X), that uses a changed partition layout.
To upgrade current "Shelly HomeKit" devices to this release the valid upgrade path is to:

1. Revert to Stock 1.3.3 (Hit the revert button in webui).
   Note there is a known issue in some cases that requires a reset of the device see #1547 for details. Look also there if you want to provide data that maybe would help to find the reason for this problem.
2. Upgrade Stock to current release (1.4.X, this will change partition layout)
3. Upgrade back to Shelly HomeKit Firmware (via the /ota Link) Sometimes the Stock Shelly has to be rebooted before the update works.

Your HomeKit configuration/pairing is not lost during this upgrade process. Other/wrong upgrade paths will yield an error during updating, but no harm is done if a wrong firmware is selected.

Please still only do this if you accept the risk to loose your config in case you need to reset

It should be possible to add the above procedure into the python update tool (flash-shelly.py) in the future for an automated way to upgrade old Shelly HomeKit devices. If anyone can help here this would be much appreciated.

Full Changelog: 2.13.2...2.13.3

Shelly HomeKit 2.13.2

Support

If you use and enjoy the firmware please consider a donation to support further development.

Changelog

Important: This release deliberately breaks the upgrade path from Shelly HomeKit 2.12.X for any Plus Devices (those are: +1, +1PM, +i4, +2PM, +RGBWPM, +PlugS). The reason for this is to support direct upgrade from newest stock firmware (1.4.X), that uses a changed partition layout.
To upgrade current "Shelly HomeKit" devices to this release the valid upgrade path is to:

1. Revert to Stock 1.3.3 (Hit the revert button in webui).
   Note there is a known issue in some cases that requires a reset of the device see #1547 for details. Look also there if you want to provide data that maybe would help to find the reason for this problem.
2. Upgrade Stock to current release (1.4.X, this will change partition layout)
3. Upgrade back to Shelly HomeKit Firmware (via the /ota Link) Sometimes the Stock Shelly has to be rebooted before the update works.

Your HomeKit configuration/pairing is not lost during this upgrade process. Other/wrong upgrade paths will yield an error during updating, but no harm is done if a wrong firmware is selected.

Please still only do this if you accept the risk to loose your config in case you need to reset

It should be possible to add the above procedure into the python update tool (flash-shelly.py) in the future for an automated way to upgrade old Shelly HomeKit devices. If anyone can help here this would be much appreciated.

Fixes

• +RGBWPM: fix weird behavior at 100% brightness

Feature

• +RGBWPM: support switch mode
• Support for Shelly Plus 1PM Mini

Full Changelog: 2.13.1...2.13.2

Shelly HomeKit 2.13.1

Support

If you use and enjoy the firmware please consider a donation to support further development.

Changelog

Important: This release deliberately breaks the upgrade path from Shelly HomeKit 2.12.X for any Plus Devices (those are: +1, +1PM, +i4, +2PM, +RGBWPM, +PlugS). The reason for this is to support direct upgrade from newest stock firmware (1.4.X), that uses a changed partition layout.
To upgrade current "Shelly HomeKit" devices to this release the valid upgrade path is to:

1. Revert to Stock 1.3.3 (Hit the revert button in webui).
   Note there is a known issue in some cases that requires a reset of the device see #1547 for details. Look also there if you want to provide data that maybe would help to find the reason for this problem.
2. Upgrade Stock to current release (1.4.X, this will change partition layout)
3. Upgrade back to Shelly HomeKit Firmware (via the /ota Link) Sometimes the Stock Shelly has to be rebooted before the update works.

Your HomeKit configuration/pairing is not lost during this upgrade process. Other/wrong upgrade paths will yield an error during updating, but no harm is done if a wrong firmware is selected.

Please still only do this if you accept the risk to loose your config in case you need to reset

It should be possible to add the above procedure into the python update tool (flash-shelly.py) in the future for an automated way to upgrade old Shelly HomeKit devices. If anyone can help here this would be much appreciated.

Fixes

• Avoid Crashloop in conjunction with Sensor Swap on GDO
• Allow Decimals in Offset correction for sensors

Full Changelog: 2.13.0...2.13.1

Shelly HomeKit 2.13.0

Support

If you use and enjoy the firmware please consider a donation to support further development.

Changelog

Important: This release deliberately breaks the upgrade path from Shelly HomeKit 2.12.X for any Plus Devices (those are: +1, +1PM, +i4, +2PM, +RGBWPM, +PlugS). The reason for this is to support direct upgrade from newest stock firmware (1.4.X), that uses a changed partition layout.
To upgrade current "Shelly HomeKit" devices to this release the valid upgrade path is to:

1. Revert to Stock 1.3.3 (Hit the revert button in webui)
2. Upgrade Stock to current release (1.4.X, this will change partition layout)
3. Upgrade back to Shelly HomeKit Firmware (via the /ota Link)

Your HomeKit configuration/pairing is not lost during this upgrade process. Other/wrong upgrade paths will yield an error during updating, but no harm is done if a wrong firmware is selected.

It should be possible to add the above procedure into the python update tool (flash-shelly.py) in the future for an automated way to upgrade old Shelly HomeKit devices. If anyone can help here this would be much appreciated.

Features

• Uses new partition layout for Plus Devices and thus can directly be upgraded from Stock FW 1.4.X and reverted back to 1.4.X but no longer from Stock 1.3.3 or Shelly HomeKit 2.12.X
• Shelly Plus AddOn: support up to 5 DS18B20 sesnsors by @markirb in #1530
• Garage door optionally support swapped sensors by @markirb in #1527
• Support for Offset Value on Temperature Sensors

Fixes

• Fix Mini 1 Gen 3 Relais not working immediately after update by @markirb in #1521

Full Changelog: 2.12.2...2.13.0

Shelly HomeKit 2.12.2

Changelog

New Model Support

• Plus 1 Mini
• Plus RGBWPM (thanks to @lanmarc77 for pinning and testing)
• Mini 1 Gen3 (thanks to @metaljay for hardware)
• Mini 1PM Gen3

Fixes

• Plug S not retaining configuration

Support

If you use and enjoy the firmware please consider a donation to support further development.

Full Changelog: 2.12.1...2.12.2

Shelly HomeKit 2.12.1

What's Changed

This is the first release in a long time.
Thanks to all contributors, testers and supporters.

If you use and enjoy the firmware please consider a donation to cover for hardware and hours lost along the way.

Short Version

this is the condensed version, for contributors and details please see long version below

New Model Support

• Plus 2PM
• Plus Plug S (without LED support)
• Plus Addon support for all supported Plus Models

New Features

• Web UI Dark Mode
• HomeKit Adaptive Lighting for CCT Lights
• HomeKit Carbon dioxide and Monoxide sensors
• DHT Sensor Support for all Addons

Fixes

• Upgradability from newer stock firmware versions
• PWM behavior at 100% for lights
• Uni: use Noisy Inputpin for debouncing Input
• Various small fixes see below

Long

• Align top logo header by @web-premiere in #1060
• Introduce CSS variables by @ladvoc in #1083
• Support Dark Mode & UI issues fix by @Idomo in #1145
• require confirmation on password change by @timoschilling in #1154
• ShellyUni: use noisyinputpin for debouncing by @markirb in #1160
• code format fix for github actions clang-format by @markirb in #1176
• use custom build of mgos/esp32-build docker image by @timoschilling in #1192
• improve rgbw and cct labeling by @timoschilling in #1195
• improve power meter by @timoschilling in #1196
• [Script] fix wifi info for stock and pre 2.11.0 fw by @andyblac in #1003
• adaptive lighting support for CCT lights by @markirb in #1028
• implement carbon dioxide and monoxide sensors by @timoschilling in #1210
• option to invert hap state by @timoschilling in #1224
• make nameserver configurable by @timoschilling in #1206
• gdo option to use second output by @timoschilling in #1205
• fix pwm behavior at 100% by @timoschilling in #1227
• fix code gen with non alphanum chars ssid by @timoschilling in #1226
• implement api toggle for switch and lightbulb by @timoschilling in #1235
• Fix complaint when zeroconf returns props with a value of None by @pmkane in #1358
• Fix for stock upgradability on Plus Models; Github Workflow by @markirb in #1387
• Addon unification / DHT support / addon as switch / plus addon support by @markirb in #1340
• refactor supported device list by @timoschilling in #1190
• Plus2PM Support by @markirb in #1388
• Add basic support for Shelly Plus Plug S by @trucidare in #1305
• Check DHT Sensor values for errors by @markirb in #1392
• Plusaddon/digital in by @markirb in #1396

New Contributors

• @web-premiere made their first contribution in #1060
• @ladvoc made their first contribution in #1083
• @Idomo made their first contribution in #1145
• @pmkane made their first contribution in #1358
• @trucidare made their first contribution in #1305

Full Changelog: 2.11.2...2.12.1

Shelly HomeKit 2.11.2

Fixes:

• Fix reverting to stock for Plus devices
• Increase power reporting interval to 5-ish seconds

Full commit log.

If updating multiple devices, you may find it easier with a script.

Please consider supporting development by donating: